Graco SMVector - Frequency Inverter Bedienungsanleitung PDF herunterladen (Seite 44)

SV01M

Commissioning

4.5.7 Diagnostic Parameters

Code

Display Range (READ ONLY) IMPORTANT

No. Name

Fault History • Displays the last 8 faults

• Format: n.xxx where: n = 1..8,

1 is the newest fault; xxx = fault message (w/o the

• Refer to section 5.3

Software Version Format: x.yz

Drive ID A ﬂashing display indicates that the Drive ID stored in the EPM

does not match the drive model it is plugged into.

Internal Code Alternating Display: xxx-; -yy

DC Bus Voltage 0 {VDC} 1500

Motor Voltage 0 {VAC} 1000

Load 0 {%} 255 Motor load as % of drive’s output current rating.

Refer to section 2.3.

Motor Current 0.0 {A} 1000 Actual motor current

Torque 0 {%} 500 Torque as % of motor rated torque (vector mode only)

Output Power kW 0.00 {kW} 650.0

Total kWh 0.0 {kWh} 9999999 Alternating display: xxx-; yyyy when value exceeds 9999

Heatsink Temp 0 {°C} 150 Heatsink temperature

0-10 VDC Input 0.0 {VDC} 10.0 Actual value of signal at TB-5 (See P162)

4-20 mA Input 0.0 {mA} 20.0 Actual value of signal at TB-25 (See P162)

TB-5 Feedback P204 P205 TB-5 signal value scaled to PID feedback units (See P162)

TB-25 Feedback P204 P205 TB-25 signal value scaled to PID feedback units (See P162)

Network Feedback P204 P205 Network signal value scaled to PID feedback units

Analog Output 0 {VDC} 10.0 Refer to P150…P155

Actual Output

Frequency

0 {Hz} 500.0

Network Speed

Command

0 {Hz} 500.0 Command speed if (Auto: Network) is selected as the speed

source

Terminal and

Protection Status

Indicates terminal status using segments of the LED display.

(Refer to section 4.5.7.1)

Keypad Status Indicates keypad button status using segments of the LED

display. (Refer to section 4.5.7.2)

Total Run Time 0 {h} 9999999 Alternating display: xxx-; yyyy when value exceeds 9999

Total Power On Time 0 {h} 9999999

Fault History 1 8 • Displays the last 8 faults

• Format: n.xxx where: n = 1..8,

1 is the newest fault; xxx = fault message (w/o the .)

• Refer to section 5.3

Fault History Time 0 {h} 999999 Display: “n.hh-” “hhhh” “mm.ss” = fault #, hours, seconds

The “hhhh” screen is displayed after hours exceed 999.

Fault History Counter 0 255 Number of sequential occurrences of a fault.

For example: 3 external faults occur over a period of time

with no other errors occurring. Then P552 will indicate 3,

P550 will indicate the error EF and P551 will indicate the

time of the ﬁrst fault occurrence.

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 65 66

Kommentare zu diesen Handbüchern

Keine Kommentare

Graco SMVector - Frequency Inverter Bedienungsanleitung Seite 44

Kommentare zu diesen Handbüchern