Graco 313296J Bedienungsanleitung Seite 25
- Seite / 108
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Setup
313296J 25
Load Material
NOTE: Before loading material, ensure that there is
a minimum overhead clearance of 105 in. (267 cm)
and all air regulators are backed off to their full
counterclockwise position.
NOTE: Follow steps below for both rams if using a
tandem warm melt supply system.
1. Refer to F
IG
. 2, F
IG
. 3, and F
IG
. 4. Close all air regu-
lators and air valves.
2. Open main air slider valve (BA) and set ram air reg-
ulator (BB) to 40 psi (0.28 MPa, 2.8 bar). Set direc-
tor valve handle (BC) to UP and let the ram rise to
its full height. 2-Button Interlock: If the system has
this feature, ram will stop as it nears the top. Press
and hold both buttons to raise ram completely. See
F
IG
. 5 on page 11.
3. Lubricate the platen seals (D) with grease or other
lubricant compatible with the fluid you will pump.
4. Remove the drum cover and smooth the surface of
the fluid with a straightedge.
5. Put a full drum of fluid on the ram base, slide it back
against the drum stops, and center it under the
platen (D). An optional drum roller kit is available to
make it easier to load the drum on the base. Order
Kit 255627.
6. Remove bleed stick from platen bleed port (J). See
F
IG
. 17.
7. If drum has a plastic liner, pull it over edge of drum.
Secure liner with tape wrapped around circumfer-
ence of drum.
8. Set the director valve (BC) to DOWN and lower the
ram until fluid appears at the top of the platen bleed
port (J). Adjust ram air regulator (BB) as needed.
Set the director valve (BC) to neutral and close the
platen bleed port (J). 2-Button Interlock: If system
has this feature, press and hold both buttons to start
lowering the ram. See F
IG
. 5, page 11.
Moving parts can pinch or amputate fingers. When
the pump is operating and when raising or lowering
the ram, keep fingers and hands away from the
pump intake, platen, and lip of the drum.
NOTICE
Do not use a drum of material that has been dented or
otherwise damaged; damage to the platen wiper can
result.
F
IG
. 17: Heated Platen
J
D
D200 Shown
- Warm Melt Supply 1
- Contents 2
- Related Manuals 3
- 4 313296J 4
- Warnings 5
- 6 313296J 6
- Overview 7
- Component Identification 8
- Tandem Supply Systems 9
- Integrated Air Controls 10
- Air Line Accessories 11
- Communications Gateway 11
- Fluid Control Module 12
- User Interface 13
- Depressurizing the 14
- Tandem ram: 14
- Single ram: 14
- 313296J 15 15
- User Interface Display 16
- Installation 17
- Connect Power Source 18
- Install/Adjust Drum Low or 19
- Empty Sensor 19
- Light Tower Accessory 19
- Attach Drum Stops 20
- Check Resistance 21
- Heater Resistance Checks 22
- Hose Installation and Care 23
- Overview of Temperature 23
- Control Settings 23
- Purge System 24
- Set Values on Display Module 24
- Load Material 25
- System Heat Up 26
- 313296J 27 27
- Operation 28
- Automatic Crossover 29
- Manual Crossover 29
- Recirculate Function 30
- Depressurize Function 30
- Change Drums 31
- Maintenance 32
- Platen Maintenance 33
- Electrical Enclosure 34
- Pump Heaters 35
- Diagnose Alarms 36
- Clear Alarms 36
- 313296J 37 37
- 38 313296J 38
- 313296J 39 39
- 40 313296J 40
- 313296J 41 41
- 42 313296J 42
- 313296J 43 43
- Troubleshooting 44
- 313296J 45 45
- 46 313296J 46
- Air Motor 47
- Displacement Pump 48
- Install Displacement Pump 49
- Disconnect Pump from Platen 50
- Connect Pump to Platen 51
- Replace Pump Heaters 51
- Replace Platen Heaters and 52
- 313296J 53 53
- Replace Platen Wipers 54
- Replace Ram Piston Rod Seals 54
- Software 56
- Replace Circuit Breakers 57
- Replace Electrical Enclosure 57
- Display/User Interface 58
- Replace Fluid Control Module 59
- Replace Cable Track 60
- Electrical Schematics 61
- D200 Ram A Schematic 62
- D200 Ram B 63
- Schematic 63
- D200 Junction Box Schematic 65
- D200 Cable Track Schematic 66
- D60 Single Ram Schematic 67
- D60 Ram A Schematic 68
- D60 Ram B 69
- D60 Pump and Platen Schematic 70
- D60 Junction Box Schematic 71
- D60 Cable Harness Schematic 72
- 313296J 75 75
- 76 313296J 76
- 313296J 77 77
- Kit 24D016 Shown 78
- 313296J 79 79
- 80 313296J 80
- UBFB 81
- 82 313296J 82
- Kit 24D010 Shown 83
- 84 313296J 84
- 313296J 85 85
- 313296J 87 87
- Platen 24D066 (20L) Shown 88
- 313296J 89 89
- Electrical Enclosure Parts 90
- Accessories 92
- Display Overview 93
- Display Details 93
- Soft Keys 94
- Navigation within Screens 94
- Setup Mode Screens 95
- Maintenance Setup Screen 96
- Hardware Setup Screens 97
- Advanced Setup Screens 98
- Advanced Setup Screen 3 99
- Run Mode Screens 100
- Heat Run Screen 101
- Status Screen 102
- Maintenance Screen 102
- Icon Function 102
- 313296J 103 103
- Dimensions 104
- D60 Models 105
- Technical Data 106
- 313296J 107 107
- Graco Standard Warranty 108
- Graco Information 108
Verwandte Produkte und Handbücher für Nein Graco 313296J
Nein Graco Crib PD171330A Bedienungsanleitung
(88 Seiten)
(88 Seiten)
(88 Seiten)
Nein Graco 3A0418E Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Nein Graco 307883G Bedienungsanleitung
(14 Seiten)
(14 Seiten)
Nein Graco 300627EN-D Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Nein Graco PD116361B Bedienungsanleitung
(40 Seiten)
(40 Seiten)
Nein Graco 3A2805K Bedienungsanleitung
(52 Seiten)
(52 Seiten)
Nein Graco 3A1334E Bedienungsanleitung
(32 Seiten)
(32 Seiten)
Nein Graco 3A1333A Bedienungsanleitung
(6 Seiten)
(6 Seiten)
Nein Graco Husky 1050HP Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Nein Graco 311014D Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Nein Graco 3A1495C Bedienungsanleitung
(16 Seiten)
(16 Seiten)
(1 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.099 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern