Graco MAGNUM 261800 Bedienungsanleitung

Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441Copyright 2007, Graco Inc. is registered to I.S. EN ISO 9001ti9338aFor portable spray applications

Getting Started 10 312079A2. Fill hopper with water or compatible flushing solvent.3. Plug sprayer in a grounded outlet.4. Turn AllControl to PRIME/CL

Getting Started312079A 11Direct Immersion Setup (Alternate Spray Method)1. Set AllControl to OFF. 2. Push down on bend of handle and pivot 90°. Remove

Getting Started 12 312079APriming and Flushing Storage Fluid (Direct Immersion Method)Before you use your sprayer for the first time or begin a new sp

Getting Started312079A 13d. set AllControl to PRIME/CLEAN GUN & HOSE. 11. Continue to trigger into waste pail until you see only paint coming out

Getting Started 14 312079ASpraying TechniquesPreventing Excessive Tip Wear• Spray should be atomized (evenly distributed, no gaps at edges). Start at

Getting Started312079A 15Choosing the Correct Tip for the JobConsider coating and surface to be sprayed. Make sure you use best tip hole size for that

Getting Started 16 312079AUnderstanding Tip NumberThe last three digits of tip number (i.e.: 221413) contain information about hole size and fan width

Getting Started With Basic Techniques312079A 17Getting Started With Basic TechniquesUse the Practice Spray Board to practice these basic spraying tech

Rolling 18 312079ARollingSetup• Before assembling roller, follow Priming instructions, beginning on page 9 for Hopper Method or page 12 for Immersion

Rolling312079A 19Rolling Techniques1. Rolling vertically, roll out the letter “M”.2. Cross roll, horizontally, to spread paint.3. Finish with light, v

Warnings 2 312079AWarningsThe following warnings are for the setup, use, grounding, maintenance, and repair of this equip-ment. The exclamation point

Shutdown & Cleaning - After Hopper Method Applications 20 312079AShutdown & Cleaning - After Hopper Method Applications• For short term shutdo

Shutdown & Cleaning - After Hopper Method Applications312079A 2113. To preserve paint in hose:a. Add enough water or cleaning solvent to refill ho

Shutdown & Cleaning - After Hopper Method Applications 22 312079APower Flush Power flushing is a faster method of flushing. It can only be used af

Shutdown & Cleaning - After Hopper Method Applications312079A 2315. To preserve paint in hose:a. Point gun into paint pail.b. Unlock gun trigger l

Shutdown & Cleaning - After Direct Immersion Method Applications 24 312079AShutdown & Cleaning - After Direct Immersion Method ApplicationsPai

Shutdown & Cleaning - After Direct Immersion Method Applications312079A 2512. To preserve paint in hose:a. Point gun into paint pail.b. Unlock gun

Shutdown & Cleaning - After Direct Immersion Method Applications 26 312079APower Flush Power flushing is a faster method of flushing. It can only

Shutdown & Cleaning - After Direct Immersion Method Applications312079A 2715. To preserve paint in hose:a. Point gun into paint pail.b. Unlock gun

Shutdown & Cleaning - After Direct Immersion Method Applications 28 312079ACleaning Roller 1. Relieve Pressure, page 7.2. Remove roller cover (a)

Storage312079A 29StorageShort Term Storage (up to 2 days)1. Turn AllControl to OFF. Pause 2-3 seconds to allow pressure to be relieved, then turn to S

Warnings312079A 3EQUIPMENT MISUSE HAZARDMisuse can cause death or serious injury.• Do not exceed the maximum working pressure or temperature rating of

Storage 30 312079AStowing Sprayer1. Use inlet screen handle to install inlet screen into hopper.2. Coil hose and leave it connected to sprayer.3. If n

Troubleshooting312079A 31TroubleshootingCheck everything in this Troubleshooting Table before you bring the sprayer to a Graco/MAGNUM autho-rized serv

Troubleshooting 32 312079APump does not prime. In Immersion Mode suction tube is not immersedMake sure suction tube is immersed in paint.Suction tube

Troubleshooting312079A 33When paint is sprayed, coat is not covering.Coat is going on too thin. Make sure gun is close enough to surface.Motor is hot

Maintenance and Service 34 312079AMaintenance and ServiceCaring for SprayerKeep sprayer and all accessories clean and in good working order.To avoid o

Technical Data312079A 35Technical DataWorking pressure range 0-2800 psi (0-19 MPa, 0 -193 bar)Electric motor 6.3 AMP (open frame, universal)Operating

Graco Standard Warranty 36 312079AGraco Standard WarrantyGraco warrants all equipment referenced in this document which is manufactured by Graco and b

Installation 4 312079AInstallationGrounding and Electric RequirementsSprayer must be grounded. Grounding reduces the risk of static and electric shock

Component Identification312079A 5Component IdentificationProject Painter 5AAllControl™ • STORAGE: for long term or overnight shutdown and stor-age.• O

Component Identification 6 312079ABCHFGAJDE1GKNBottom view and position for direct immersion modeRSTUWLPti9724ati9168aVXMti9305ati9374ati9533ati9301at

Getting Started312079A 7Getting StartedPressure Relief ProcedureFollow this Pressure Relief Procedure when you stop spraying and before cleaning, chec

Getting Started 8 312079AAllControl™ SettingsSetupProject Painter 5 can be used as either a hopper or direct immersion sprayer. Hopper Method (Primary

Getting Started312079A 96. Connect other end of hose to sprayer (a). Use two wrenches to tighten securely.7. Push down on bend of handle and pivot 90°