Graco 3A1698F Bedienungsanleitung

3A1698FOperationFine Finish Hand-Held Paint Sprayer- For portable spray applications of architectural paints and coatings only -- Not approved for use

Common Procedures 10 3A1698FSetting Hi/Lo Switch (Motor Speed)1. To extend battery life, try spraying with low motor speed to get an acceptable spray

Setup3A1698F 11SetupFlexible Suction TubeThis sprayer comes with a suction tube that can be adjusted for multi-directional spraying. Spraying Ceilings

Setup 12 3A1698FSprayer SetupThis sprayer arrives from the factory with a small amount of test material in the system. It is important that you flush

Starting a New Job (or Refilling the Cup)3A1698F 13Starting a New Job (or Refilling the Cup)1. Engage trigger lock and put prime/pressure relief valve

Install Tip/Guard Assembly (if not installed) 14 3A1698FInstall Tip/Guard Assembly(if not installed)NOTE: Only use Graco Fine Finish Tip/Guard assembl

Unclogging Spray Tip/Guard Assembly3A1698F 15Unclogging Spray Tip/Guard Assembly1. To unclog tip obstruction, engage trigger lock and put prime/pressu

Shutdown and Cleaning 16 3A1698FShutdown and CleaningFlushing Sprayer1. Engage trigger lock and pull prime/pressure relief valve UP to release pressur

Shutdown and Cleaning3A1698F 178. Disengage trigger lock, reverse tip to UNCLOG position, and pull trigger for 5 seconds to prime sprayer.9. Put prime

Storage 18 3A1698FCleaning Sprayer Exterior• Wipe paint off outside of sprayer using a soft cloth moistened with water or flushing fluid. Do NOT subme

Replacement Parts and Kits3A1698F 19Replacement Parts and Kits5120531404159342321212057563811131517171214163664353942434544463133372725266730292868910

Table of Contents 2 3A1698FTable of ContentsWarnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Grounding Instruct

Replacement Parts and Kits 20 3A1698FParts ListRef.If you have this model sprayer (model number is the same as the part number, which is below the han

Replacement Parts and Kits3A1698F 2132 Models 16F887, 16H241, 16H242, 16H829 16U240 Enclosure replacement kit (includes 20, 34-37, 38 (qty 10), 39, 44

Replacement Parts and Kits 22 3A1698F61 Model 16H241 only 124783 Plug Adapter62-70 Models 16F887, 16H241, 16H242, 16H829 16U240 Enclosure replacement

Alternate Priming Method3A1698F 23Alternate Priming MethodIf sprayer fails to prime, the inlet valve may be stuck due to paint residue. Perform the st

Inlet Valve Removal/Service 24 3A1698FInlet Valve Removal/Service1. Engage trigger lock and pull prime/pressure relief valve UP to release pressure.2.

Outlet Valve Repair3A1698F 25Outlet Valve RepairNOTE: Before doing any repair to pump, perform Flushing Sprayer procedure, page 16.Removal1. Engage tr

Troubleshooting 26 3A1698FTroubleshootingCheck everything in this Troubleshooting Table before you bring the sprayer to an authorized service center.P

Troubleshooting3A1698F 27Spray Pattern DiagnosticsSprayer sprays with poor results Tip is partially clogged See Unclogging Tip/Guard Assembly, page 15

Troubleshooting 28 3A1698FSpray pattern has dripping:Sprayer is moving too slow for material. Move sprayer faster while spraying.Sprayer is too close

Technical Data3A1698F 29Technical DataSprayer:Adjustable Pressure Range 500 to 1500 psi (34 to 103 bar, 0.34 to 10.3 MPa)Maximum working pressure 170

Warnings3A1698F 3WarningsThe following warnings are for the setup, use, maintenance, and repair of this equipment. The exclamation point symbol alerts

Preferred Material Settings Log 30 3A1698FPreferred Material Settings LogDateItem SprayedMaterial SprayedSpray TipMotor Speed(Circle One)Pressure Sett

Notes3A1698F 31Notes

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves th

Warnings 4 3A1698FWARNINGWARNINGWARNINGWARNINGFIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint fumes, in work area can ignite or e

Warnings3A1698F 5EQUIPMENT MISUSE HAZARDMisuse can cause death or serious injury.• Disconnect the battery before servicing.• Always wear appropriate g

Warnings 6 3A1698FPRESSURIZED ALUMINUM PARTS HAZARDUse of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemic

Component Identification3A1698F 7Component Identification*NOTE: Tip filter is reverse-threaded. Turn left (or counter-clockwise) to tighten, turn righ

Charging the Battery 8 3A1698FCharging the BatteryBatteries are initially 50% charged to provide optimum bat-tery life and require charging before fir

Common Procedures3A1698F 9Common ProceduresTrigger LockPrime/Pressure Relief Valve PositionPressure Relief Procedure4. Engage trigger lock. 5. Put pri