Graco 3A0410D Bedienungsanleitung

OperationHusky® 3300 Air-Operated Diaphragm Pump3A0410DENHeavy-duty 3-inch pump with large flow paths for fluid transfer applications, including high-

Installation 10 3A0410DSolvent containers used when flushing: Follow local code. Use only conductive metal containers, placed on a grounded surface. D

Installation3A0410D 11Air Exhaust Ventilation.To provide a remote exhaust:1. Remove the muffler (U) from the pump air exhaust port (K). 2. Install a g

Operation 12 3A0410DOperationPressure Relief Procedure1. Shut off the air supply to the pump.2. Open the dispensing valve, if used.3. Open the fluid d

Operation3A0410D 13Pump ShutdownAt the end of the work shift and before you check, adjust, clean or repair the system, follow the Pressure Relief Proc

Operation 14 3A0410DTorque InstructionsSee FIG. 5 for fluid cover and air valve fasteners. See FIG. 6 for manifold fasteners.NOTE: Fluid cover and man

Operation3A0410D 15FIG. 6. Torque Instructions - Manifold FastenersPolypropyleneti16564a10911121314151617181920212223241-8Aluminumti16559a121110914131

Aluminum Pump Dimensions 16 3A0410DAluminum Pump Dimensionsti16557ati16558ati16559aABDCEFGAir Inlet(opposite side from muffler)HJKLMA 24.50 in. (62.2

Polypropylene Pump Dimensions3A0410D 17Polypropylene Pump Dimensionsti16562ati16563ati16564aABCDHJKLEFGAir Inlet(opposite side from muffler)MA 36.80 i

Stainless Steel Pump Dimensions 18 3A0410DStainless Steel Pump Dimensionsti17455ati17456ati17457aABCDHJKLEFGMAir Inlet(opposite side from muffler)A 23

Performance Charts3A0410D 19Performance ChartsTest Conditions: Pump tested in water with inlet submerged.ABCDHow to Read the Charts1. Locate fluid flo

Related Manuals 2 3A0410DContentsRelated Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2To Order a New Pump . . . . . . . . . . . .

Technical Data 20 3A0410DTechnical DataHusky 3300US MetricMaximum fluid working pressureAluminum or Stainless Steel withAluminum Center Section125 psi

Technical Data3A0410D 21Inlet/Outlet SizesFluid inlet - Polypropylene3 in. ANSI/DIN flangeFluid inlet - Aluminum3 in.-8 npt or 3 in.-11 bspt with 3 in

Technical Data 22 3A0410DFluid Temperature Range* The maximum temperature listed is based on the ATEX standard for T4 temperature classification. If

Technical Data3A0410D 23

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves th

To Find Your Nearest Distributor3A0410D 3To Find Your Nearest Distributor1. Visit www.graco.com.2. Click on Where to Buy and use the Distributor Locat

Configuration Number Matrix 4 3A0410DConfiguration Number MatrixCheck the identification plate (ID) for the 20-digit Configuration Number of your pump

Warnings3A0410D 5WarningsThe following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-tion point s

Warnings 6 3A0410DEQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury.• Do not operate the unit when fatigued or under the influence of d

Warnings3A0410D 7TOXIC FLUID OR FUMES HAZARDToxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or sw

Installation 8 3A0410DInstallationOverviewThe Typical Installation shown in FIG. 1 is only a guide for selecting and installing system components. Con

Installation3A0410D 9Tighten FastenersBefore mounting and using the pump for the first time, check and retorque all external fasteners. Follow Torque